Atmel at89c55 projectработы

write source or help trouble shoot using debugging tools our existing code. C (Arduino IDE) but prefer to use Atmel Studio Using ATmega328 or ATMega168P QFP CPU Monitor 5 I/O pins - to determine if a switch contact is open or closed Closed is Good, open is alarm condition Also use A/D to drive an LM84T temperature sensor and measure once per minute Alarm condition if temperature is over 75C once per 5 minutes - use serial lines to operate and send a message using HopeRF RFM95 LORA radio module. (this is a 'status ok' message) We have library for this radio module When alarm conditions occur (contact open or temperature >75C) alarm message sent. Message payload is 6bits - we have this defined. Device sends messages only 1650mAH battery - target 5 years life We have this...

... hardware proto testing code implementation. making calculations of product dimensions, drawing sketches of product ideas, and designing mockups of proposed products. Develop and complete projects Sourcing of raw materials. Purchase electronics device and equipments depending upon project needs Troubleshooting embedded systems and diagnosing errors, malfunctions, or inefficiencies firmware drivers for hardware peripheral ICs. Analog, Digital, mixed signal, wireless & rf electronics design. Microcontroller (Atmel, ST, Renesas, Microchip, ARM etc.) based system design,development, and testing, Embedded C/C++ Programming. Implementing effective repairs, modifications, and upgrades to the embedded systems Schematic creation according to hardware design and PCB layout desig...

Hi, How are you doing. I am looking for electrical engineers to work on multiple tasks in following areas: • Embedded C Programming. • VHDL/Verilog, LABView/ Multisim/PSPICE • Network Simulator NS2/NS3 • Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC and STM32. • IDEs like Keil MDK V5, ATmel studio and MPLab XC8. • PLCs / SCADA • PCB Designing-Proteus, Eagle. • IOT Technologies like Ethernet, GSM GPRS. • HTTP Restful APIs connection for IOT Communications. I am looking for long term work relationship. New freelancers are warmly welcomed. Important Note: I need dedicated freelancers who strictly follow the deadline and give me good quality work without any plagiarism.

I want to generate an I2C slave with a SAMD21. This should have write and readable registers. Unfortunately I can't get this to work. I was guided by the following code: From page 39: The final application “High speed Configuration” in main.c file will be as below for SLAVE. The aim is to provide 256 registers (1 byte in size) with the SAMD21 (as Slave). The I2C master can write and read these registers. Your task is to create this functionality based on the provided example. Only the function "void SERCOM2_Handler(void)" may be adjusted. The I2C master works in FAST_MODE_PLUS. Therefore, the rest of the configuration must remain exactly the same.

Hi Sardar I need you to write a research report on Atmel comparison with PIC chip. I need 20 pages report with references and tables.

Miniature battery operated circuit with a few I/Os driving a solenoid. Expertise with a Nordic, Atmel or similar Wireless Microchip is a plus. Located Tulsa, Oklahoma, USA

We require a embedded software developer to examine the program and change it according to the new PCB also require you to write libraries and working code without altering the other functions. The component in question that has been replaced is a capacitive sensor IC used for touch buttons. Please bid only if you have good knowledge and experience working Atmel studio, Arduino IDE ,Atmel and Arduino libraries ,ESP and atmega controllers , capacitive proximity sensing ICs. We need you to coordinate with backend developers and mobile application developers to test the functionality We have multiple development projects upcoming and you could be our preferred freelance team member. We could Discuss on the Pricing and come up with a mutually agreeable figure.

We have a display currently using an Atmel Mega 8 processor with RS-232 input. It now needs Ethernet input and program upgrading via the Ethernet

Atmel microcontroller programing in C language for my day to day projects

basic servo control (i.e. group actions) with ps2 controller and bluetooth android user interface. hardware is assembled, servos connected. powered with serial and bluetooth connections available.

...replace an outdated component with a new one and arrange the components in a different layout on to the PCB We also require you to write libraries and working code without altering the other functions. The component in question is a capacitive sensor IC used for touch buttons. Please bid only if you have good knowledge and experience working with CAD (any electronic cad will work),Atmel studio, Arduino IDE ,Atmel and Arduino libraries ,ESP and atmega controllers , capacitive proximity sensing ICs. We need you to coordinate with backend web application developers and mobile application developers to test the functionality We have multiple development projects upcoming and you could be our preferred freelance team member. We could Discuss on the Pricing and come up with a...

To work on legacy programs - debug and later re-wrie Preferably Southern England

Для просмотра деталей, пожалуйста, зарегистрируйтесь или войдите в систему.

I am new to Atmel Studio and having lots of trouble when building a project that I inherited. I need interactive help on Zoom.

Convert assembly code to C for ATMEL ATSAM4SD16CA-AU

Для просмотра деталей, пожалуйста, зарегистрируйтесь или войдите в систему.

I want to analyze the code . There is a part I want to detect.

We have a pcb deisng with firmware that works quite well, we would like to add a couple of features (additional input contact and ntc reading) and so a redesign and a firmware change is required. We need a development company with a lot of experience with pcb design and atmel platform. No prototype needed, we will take care of that. Please begin you bid with atmel, to be sure you read the above. Otherwise your bid will not be considered. Many thanks

I am looking for a professional Atmel firmware engineer with experience in Zigbee protocol. Our custom board is designed to send data over Zigbee. The other parts are working great. We just have an issue in Zigbee communication. It is mainly related with the Zigbee message packet. I can provide with the existing Atmel source code. The task is to review the existing project and resolve the Zigbee communication issue. Only apply if you have experience with Zigbee. To prove that you are serious, please start your proposal with a word "zigbee".

Для просмотра деталей, пожалуйста, зарегистрируйтесь или войдите в систему.

Guten Tag, können Sie eine bestehende Software für einen ATMEL Chip ändern?

We are looking for electrical and electronics engineers with good experience in following areas: • Embedded C Programming. • VHDL/Verilog, LabVIEW/ Multisim/PSPICE • Network Simulator NS2/NS3 • Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC and STM32. • IDEs like Keil MDK V5, ATmel studio and MPLab XC8. • PLCs / SCADA • PCB Designing-Proteus, Eagle. • IOT Technologies like Ethernet, GSM GPRS. • HTTP Restful APIs connection for IOT Communications. Feel free to place your bid and mention your areas of expertise in your proposal. we highly encourage new freelancers to apply for this post.

Guten Tag, für ein bestehendes Projekt suche ich einen C Programmierer um einige Änderungen vorzunehmen. Ich glaube es ist in C geschrieben :-) Chip: ATXMEGA128A4U-MH Hier ein Auszug aus der main.c /** * file * * brief PS2-101 Ps - application entry point * */ /* * Include header files for all drivers that have been imported from * Atmel Software Framework (ASF). */ #include <asf.h> #include "as3911.h" #include "as3911_com.h" #include "as3911_interrupt.h" #include "iso14443a.h" #include "clock.h" #include "ic.h" #include "uart.h" #include "delay_wrapper.h" #include "sorex_hal/Communication/Rfid.h" #include "utils/debug.h" #include "utils/reschedule....

The project is to add the circuit into existing PCB. The circuit is offered. The designer will update the schematic and PCB. And if you know about firmware development for ATXMEGA128AiU and Atmel studio 7, it is preferred.

We would like to have developer, who can develop atmel or arduino devices which have 6 I/O and data output need in CSV format. Which can be communicate thre BT or Wifi to server or app.

The project is about programming an operational flow in an ATmega128 Atmel Micro-Controller. Application is controlled via a Nextion Touch Display. As per input on display, complete operation is to be executed to turn ON/OFF the peripherals. Number of Peripherals to be controlled: Digital Output: 17 (ON/OFF or HIGH/LOW) Digital Input: 07 (HIGH/LOW) Analog Input: 04 Nextion Touch Display GUI & Atmel128 Arduino IDE code is implemented. Freelancer just need to implement process level flow program. Request to freelancer to ask for more operation level details if interested.

Need an example written for a SAML22 processor using ASF4 which allows for a multiple-input 12bit ADC reading. It is simple for anybody who knows Atmel products. Need to be able to read and convert a set of ADC inputs. Must have experience with AMM and SAM processors.

Assistance needed in porting code written for a PIC18F26K to a more modern model (that is in stock). Program is about 400 lines of C, I suspect the model number may need to be changed and a few pins remapped, but otherwise ...PIC18F26K to a more modern model (that is in stock). Program is about 400 lines of C, I suspect the model number may need to be changed and a few pins remapped, but otherwise the code is usable. Currently using 1 A/D, TX/RX for serial and 4 GPIO pins. The code is doing battery management. If it is less time the code could be ported to Atmel or Arduino if decided, it is not doing a whole lot. Bonus points if you are familiar with Raspberry Pi. This project sends data via serial to the Pi and that also needs some updates. Can discuss that further after t...

The task consist to create a bootloader for the SAMD21E17A Microcontroller based on the Microsoft/Adafruit UF2 Bootloader. It needs to be compatible with Arduino for uploading the code, customer requirement. The bootloader has been compiled, however there is no way to communicate with Arduino IDE. Variants were based on TAU and Trinket m0, no luck. It will be probably an easy fix, but I am stuck with it. Looks like some linker script or BOSSA configuration is wrong. I will share my code with you if you need it. Required skills/equipment: - linux/unix environment - C language - Development board with SAMD21E18 or E17 (not a must)

I am looking for electrical engineers to work for me on long term basis. I need engineers in different domains of electrical engineering. • Embedded C Programming. • VHDL/Verilog, LABView/ Multisim/PSPICE • Network Simulator NS2/NS3 • Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC and STM32. • IDEs like Keil MDK V5, ATmel studio and MPLab XC8. • PLCs / SCADA • PCB Designing-Proteus, Eagle. • IOT Technologies like Ethernet, GSM GPRS. • HTTP Restful APIs connection for IOT Communications.

We will keep on purchasing the products from ATMEL&Cypress in San Jose of CA, every month. We need the candidate with the products experience sales,purchasing,or R&D and better to live in the city . We have head office in Shanghai and representative office in VA,USA now and we are prepering to build up one chip technology company for the automotive industry.

We are one high-tech company headquatered in Shanghai city,CHINA, with business of automotive industry grade chip's IDM supplier design,tapeout,foundry,packaging, test,sales and international trade. We are active to seek some purchasi...chip's IDM supplier design,tapeout,foundry,packaging, test,sales and international trade. We are active to seek some purchasing managers for automotive chip in the countries and regions for chip manafacturers,especially in USA,Japan, Europe. For one purchasing manager for every chip manafacturer incl. TI(in DALAS),Diodes(in Dalas),Freescale(in Austin),ONSEMI and MICROCHIP( both in AZ),ATMEL and Cypress (both in San Jose of CA)Allegro(in NH,or MA),RENESAS (in Japan)ST (in Italy and French),Infineon (in Germany),TSMC(in Taiwan of ...

you just need to know how to do the pwm and adc code in c programming using atmel studio to link to servo motor, h bridge, sensor (pin) and the calculation to be completed in a few day

I am looking for an embedded system engineer who can help in bringing up an ATMEL based 32-bit ARM development/evaluation board who has experience in U-Boot, BSPs, JTAG, device drivers and utilities needed for bringing up a board.

Hi, We are looking for technical writers to write on different projects designed using Arduino, Raspberry Pi, PIC, Atmel etc. Thanks.

TARGET CPU: ATSAM4S4B-AU A The purpose is to upgrade the target CPU using the SAM-BA protocol. You create a PC (Window) GUI and provide the source. The GUI is for confirming the completion of the work. I plan to reprogram using that source. You must have an ATSAM4S4B-AU or a board ...that source. You must have an ATSAM4S4B-AU or a board similar to the ATSAM4S. I do not provide H/W. Reference: Note) Only C must be used. You must not use C++.

Buen día. *ATENCIÓN* Aplica solo si eres un programador con experiencia. Buen día, estoy desarrollando varios proyectos que requieren de mucha programación. Necesitamos alguien con conocimientos en C/C++, NodeJS, Python, PHP, Javascript, HTML, .NET. La idea es conseguir un desarrollador que trabaje con la raspberry pi y otras SBC, con experiencia en microcontroladores espressif o atmel, que sepa trabajar con linux y sus diferentes distribuciones. La idea es hacer por el momento un solo proyecto.

...Arduino based project in order to sell my product as an appliance but the certification lab is asking me for some software requirements. These software requirements are checkings and measurements that the microprocessor shall do (in this case the ATMega 328P), like for example check the frequency of the clock, memories testing... You have a general explanation here: The two documents attached explain the following: - UNE-EN : Those are the fault/error conditions that the software shall evaluate - AVR998_ Guide to IEC60730 Class B Compliance with AVR Microcontrollers. Introduction. Features. AVR 8-bit : this is a guide about how to do it for Atmel microprocessors

Proiectul trebuie realizat practic , componentele sunt cumparate .Este vorba de un senzor ultrasonic de distanta HC-SR04 care comunica cu microcontrolerul ATmega328p pe care il contine placa arduino uno .Am incarcat un pdf cu componentele cumparate .Codul trebuie scris in Microchip Studio 7 (atmel) .

Elevator c code

I need someone to write a part of a firmware to integrate it in my main project for any microcontroller(PIC microchip or Atmel or in arduino IDE) to be able to receive serial data and publish them on a channel on the Webserver MQTT and the opposite (receive/subscribe data from a channel on Webserver MQTT) . Serial Data baud rate:9600 Serial Data Type : String[200]

Eclipse IDE framework and GNU compilers

Looking for help to make Altium schematic on base of Atmel ATSAMD21, IR transcever and receiver, when piezo disc triggered sends signal to receiver to close or open contacts, basically this some sort sensor for hobby CNC machine, traceiver should have compact battery option and all parts should be available to buy

Hi, We are looking for multiple writers to write on technical topics. ** The writer must have practical experience with microcontrollers i.e. Arduino, PIC, Atmel etc. ** Please mention at the start, on which platform, you would like to write. We will provide order in bulk so looking for low prices. Thanks.

...detected from MPU 6050 and play audio tracks from MKRZero's onboard SD Card. Audio tracks need to play for: 1.) at least 1 track and, 2.) keep playing track after track while motion is detected only stop playing when motion is no longer above threshold, at which point, MKRZero returns to sleep. (if possible make the threshold for "motion" easy to change) Needs to be written for Arduino IDE or Atmel Studio 7. Below are some simple examples to help (if needed) - Simple audio player MKRZero: (This is how I wired up speaker, so code may just need copied) - Read SD Card MKRZero: - SAM example

We are a small manufacturing company producing unique and hand-made sound instruments, i.e. analog synthesizers. Our brand name is "Club Of The Knobs - Modular Analog Synthesizer" Some of our modules need Atmel chips to control functions on the boards. We need them programmed again since we have lost the previous versions. We therefore know the exact requirements for the chips and can provide the circuit schematic for the electronic environment. We are looking for someone who also knows electronics and can make the connection between the digital and the analogue.

I'm looking to do two things. 1) To create a msc bootloader for the device that a user can interact with and 2) To set up a basic project file where I can interact with the onboard IO and components (accelerometor, buzzer, vibration motor, and move files back and forth from hidden to visible msc memory). background information: There is a 2MB flash memory chip which displays 1MB to user and 1MB is hidden partition. The custom board is running a Samd21G17A, all components on the board have been verified working (Power, regulation, GPIO, USB, SPI, jlink reprogramming.) I will ship this board to you for development work. an example of this process would be; 1) the user is given a new file to reprogram the device, the user plugs device into USB 2) The user copies the file to ...

Existing AVR project needs update to 1: recognize FAT32 2:Ignore "System Volume Information" folder. Completed project will include .hex programming file and return of all updated AVR programs. There are a number of variations of the 'same' program that need to be updated. I may only have the .hex version of some of these.

Small PID with Pt100, Pt1000, Thermocouple or 4~20mA (1~5V) input. Single output with Choice of proportional (PWM) or On/Off Output. 2 x 4-digit LED displays + ancillary LEDs, simple 3-button menu with basic PID settings only. Other more complex projects to follow - pending cooperation on this project. Must show an understanding of what is required and track record on working with PIC and/or Atmel.

I (Electrical Engineer) work for a small company that makes Ethylene Oxide Sterilizers and I've got some 8 bit AVR programming work that I'm simply stretched too thin to do myself. I just got the go ahead to outsource it. We've got a mainboard and a daughterboard each running an AVR128DB-64...Have a small touchscreen display. That display is used in another released product so we have code to steal for that. Have a couple SPI and USART peripherals, boards talk to each other with i2c, some ancient parallel stuff too. Nothing about this is too hard, but we would like to have someone do it well, clean, documented, portable, etc. We have a preference that development be done with Atmel/Microchip Studio and avr gcc. If you're interested, I can get you a...