Завершен

digital alarm clock using an Arduino microcontroller. (TINKERCAD)

digital alarm clock using an Arduino microcontroller. The clock will have different functionalities implemented in it, like showing the temperature, switching between 12H and 24H modes, setting up the values for current time and alarm time, etc. via the use of buttons.

Project Details

You are expected to do the whole project solely on Tinkercad, but for those who prefer to use Proteus can also use it. (One advantage of Proteus is having more options to choose from for most components.)

You are NOT restricted to using register operations, you can use any kind of code including libraries for components (i.e. Wire.h, LiquidCrystal.h). But YOU MUST USE TIMER for timing. Do not use delay function for timing.

Requirements

- LCD screen which is showing:

1-Current time (Switchable between “00:00-24:00” and “00-12 AM/PM”)

2-Alarm time (with a symbol indicating ON/OFF)

3-Temperature (Switchable between Celsius and Fahrenheit) -4 Buttons which are used for:

B1-Switching between modes in current time

(Hold 3 seconds for current time setup) B2-Setting the alarm ON and OFF

(Hold 3 seconds for alarm time setup)

B3-Switching between temperature scales (Fahrenheit /Celcius)

(During a value setup, this button acts as “raise value ^”)

B4-Snooze button

(Temporarily stops alarm for only 5 minutes)

Piezo buzzer for the alarm sound

Potentiometer for changing backlight brightness

Temperature sensor for detecting temperature

You must use TIMERS for timing (i.e. do not use delay function to update seconds)

To see which value is being set at a given time, the time value which is being set will blink. Here is an example setup scenario of setting up alarm time:

Alarm Set Up

1-Hold B2 for 3 seconds to start setup *alarm minute will blink*

2-Use B3 to adjust alarm minute

3-Press B2 once to switch to hour *alarm hour will blink*

4-Use B3 to adjust alarm hour

5-Press B2 again to end setup

Clock Set Up

1-Hold B1 for 3 seconds to start setup *clock minute will blink*

2-Use B3 to adjust alarm minute

3-Press B1 once to switch to hour *clock hour will blink*

4-Use B3 to adjust alarm hour

5-Press B1 again to end setup

Навыки: Arduino, Электроника, Микроконтроллер, Электротехника

Показать больше: digital alarm clock, handheld digital alarm clock, html code digital alarm clock, digital alarm clock pic using code, designer digital alarm clock, digital alarm clock design, digital alarm clock days, digital alarm clock using pic, digital alarm clock using vhdl, digital alarm clock using vhdl code, digital alarm clock using verilog, digital clock using arduino uno, iot alarm clock using arduino, digital alarm clock using pic microcontroller, digital alarm clock using verilog project, smart alarm clock using arduino, digital clock using arduino and seven segment

О работодателе:
( 1 отзыв ) Istanbul, Turkey

ID проекта: #30381472

Поручен:

AdelAGh

Hello, I'm an Electrical Engineer .I have many Experiences in Matlab ,python ,C# ,VB , Microcontroller, Arduino , sensors ,PLC’s, SCADA system, circuit design , PCB ,also I have experience in programming that connect Больше

$25 USD за 2 дней(-я)
(10 отзывов(-а))
3.9

4 фрилансеров(-а) готовы выполнить эту работу в среднем за $69

soltracker

An easy project to be done, U will get the best work done..thanx................................................

$30 USD за 2 дней(-я)
(68 отзывов(-а))
4.8
ahmedali998

i read your project and I have done this before contact me I'm a mechatronics engineer i have knowledge in mathematical differential equations, Robotic and Embedded systems design, logic design, c & c++ programing Больше

$20 USD за 7 дней(-я)
(0 отзывов(-а))
0.0
LaoPhone

Hello, your project is very suitable for me. I have enough experience in Arduino firmware and Proteus simulator. I checked your requirements, and sure that I can complete it perfectly. I am ready to start working on yo Больше

$200 USD за 3 дней(-я)
(0 отзывов(-а))
0.0