В работе

atmospheric water generator (new)

I need this research paper to include specific details on manufacturing an Atmospheric water Generator to be able to fully operate it on Solar power with recycle components ( except for the condensing tubes which need to be food grade for human consumption and the water tank and water path) condensing water from atmospheric ambient air. comparison charts of different types in a table explaining why this method is the best, tabulating the different metallurgy combination of the condensing sink , why this specific combination was choose ( example resistive to rust we add brass copper for conductivity and aluminum for durability and light weight).

by using the following:

1-thermoelectric cooling module (TEC)

2-using solar energy

3-auto start and stop based on temperature and humidity ratio of sensor

4- construction design, best available thermally insulated material for the air channel

5- using least amount of electricity for air flow through duct by using convergence and divergent theorem

6-tabulating all values why any design was chosen

7-single fan to condense water from atmosphere and cool the hot side of the TEC heat sink

8- COP of the system needs to be above 2

9-Heat transfer calculation and thermodynamics wherever applicable

10-the dimensions of device 20 cm X 20 cm X 20 cm ( can be flexible whether bigger or smaller)

11-all the chosen materials and items needs a good explanation on why they were chosen such not limited to: cost, thermal conductivity, environmental reactions/impact, cooling benefits, heat loss benefits,

12-actual application to build one

13- needs to be feasible

14- can work in Dubai, U.A.E. harsh hot/humid environment

15-actual flow simulation and heat dissipation simulation

16- needs to work independently off grid

17- a micro-controller will be programmed to start and stop the device ( this needs to be taken into consideration)

18- DC power supply only

19- Solar panel selection based on comparison of all types

20-fan supply needs to be variable frequency driven (calculation that needs to be also included to be inputted in the micro controller to start and stop that system and fan speed frequency)

21- considering the formulas need to be addressed where they are used

22-TEC module selection should be also into account based on the type, output cooling quantity , placement of the TEC on the condensing sink, flow path, heat transfer calculation

23- a series of formulas that need to be inserted in the micro-controller in terms of temperature, humidity, dew point, device on / off, fan variable frequency drive, TEC module

24-user friendly to assemble and manufacture

25- engineering design

Note this document will be used along side with the actual manufacturing and application ( which I will be doing)

Квалификация: Электротехника, Электроника, Техника, Технология машиностроения, Дизайн продукта

Показать больше water bottling outsourcing cost, fresh water generator hydro anthracite filtration, build a e learning, water from air project, atmospheric water generator project, atmospheric water generator diy, portable atmospheric water generator diy, passive atmospheric water generator, atmospheric water generator for agriculture, atmospheric water generator manufacturers, atmospheric water generator prices, new website build, new zealand editor cost, write a report to your head office making feasible suggestions for opening a new branch in your city, new wordpress website cost, write a report to your head office making feasible suggestion for opening a new branch in your city, writing a report to your head office making feasible suggestions for opening a new branch in your city, Build a E-commerce website, new website build project, hot water jobs new caledonia

О работодателе:
( 0 отзыв(-а, -ов) ) Dubai, United Arab Emirates

ID проекта: #18542085



Practical designer with CAD and analysis. I have vast knowledge in power generation from hydro and solar. I have worked in hydro power station and know the dynamics of the power generation. Also, i have installed a Больше

$200 USD за 3 дней(-я)
(78 отзывов(-а))

6 фрилансеров(-а) в среднем готовы выполнить эту работу за $244


السلام عليكم I'm Mohamed Saeed. mechanical and electrical engineering expert. I have checked your job description and I'm ready to help you in your paper implementation using all mentioned topics.

$388 USD за 2 дней(-я)
(42 отзывов(-а))

Hello, I have read the details provided and i am positive i can provide quality work,please contact me to discuss more on the project deadline and some other few things

$135 USD за 4 дней(-я)
(31 отзывов(-а))

Hello! Our profile: https://www.freelancer.com/u/crtvisuals2 Checked the project's demands, we can do this. Let's have a few words before you decide the team to do this job. We're ready to start immediately. Let' Больше

$500 USD за 7 дней(-я)
(2 отзывов(-а))

I believe that my experience and skill in this background will prove to be of great help to you. Contact me to discuss more on the details

$150 USD за 4 дней(-я)
(2 отзывов(-а))

Dear Employer, I am ready to work on your required task and can also give 100% satisfaction. Looking forward to an opportunity to work with you. Warm Regards: Theata Solution

$88 USD за 3 дней(-я)
(0 отзывов(-а))