Закрыт

Re-design of UWB Radar Rx and Tx to Eliminate Obsolete Parts and Update ADC (FPGA Programming)

We have Gerbers and BOMs for a small UWB radar receiver and transmitter (1 – 100 MHz) used for ground penetrating radar applications. The boards were designed around 2007, and many of the specific parts no longer are in production (CPLD, memory, even some resistors and diodes). We require an RF engineer to go through the BOM and update the list with modern components easily sourced from DigiKey, Newark, Mouser, etc, without a significant re-design of the boards themselves.

Ideally, the successful candidate would also be able to re-write the FPGA firmware to accommodate a faster ADC chip. We are currently using an 80 MSPS 14 bit ADC (AD9245BCPZ-80), which is the fastest in that specific form factor. Ideally, we would like to go as high as 180 MSPS whilst keeping the board the same size. This would require some re-work of the board and a re-writing of the FPGA code.

We do have a design for a modern Rx board, but have no firmware for this new board as yet. One option would be to either create a hybrid Rx board, or write new firmware for the new board based on the original board’s FPGA code.

Навыки: Arduino, Электротехника, Электроника, Микроконтроллер, Разводка печатной платы

Показать больше: re-design a brochure, re)design logo, re design, Re design website, re design some business cards, re design logo, re design frosted business card, re design a site, RE design a logo, re design a logo for luxury brand, mailchimp newsletter re-design - open to bidding, logo re design, control panel re-design, complete re-design, software uwb radar

О работодателе:
( 3 отзыв(-а, -ов) ) Rawalpindi, Pakistan

ID проекта: #16629145

9 фрилансеров(-а) готовы выполнить эту работу в среднем за $37/час

ahmedmohamed85

Dear sir I am a Radar Engineer also I am the top rated FPGA programmer at freelancer.com, please check my profile also please message me so that we can discuss best regards

$50 USD / час
(201 отзывов(-а))
7.2
juanchigarin

Dear I readed your proposal and I can make your job perfectly. I design using Altium Designer and Eagle. I cant reprogramm the FPGA but I can redesign all the PCB with new components I'm electronic enginner with Больше

$27 USD / час
(14 отзывов(-а))
4.9
quandangvan

A proposal has not yet been provided

$25 USD / час
(9 отзывов(-а))
4.0
wenzhaoxu

Hi, I already read the description. I think I can do it. I am expert in Circuilt Desgin/Pcb Layout/Micro controller program. I have more than 19 years experiences. I have developed a lot of product, some of these i Больше

$50 USD / час
(7 отзывов(-а))
4.2
prakashddit

i am having experience of FPGA and verilog coding along with circuit designing

$27 USD / час
(3 отзывов(-а))
3.0
eopskzs

A proposal has not yet been provided

$40 USD / час
(0 отзывов(-а))
0.0
unboltsoft

We are Ukrainian software development company that employs several passionate engineers. Our main direction is the engineering, development and implementation of custom software with a deep scientific focus that requ Больше

$41 USD / час
(0 отзывов(-а))
0.0
ReconLogic

I can write FPGA firmware and also assist in new component selection. I have experience with xilinx and altera cpld/FPGA/SoC

$25 USD / час
(0 отзывов(-а))
0.0
muradalshorman

We are a specialized company in PCB design , we are providing the design of PCB from your schematic design to all layer PCB Gerber files .

$50 USD / час
(0 отзывов(-а))
0.0