Mixer bluetooth_

Закрыт Опубликован 3 года (лет) назад Оплачивается при доставке
Закрыт Оплачивается при доставке

What we have:

5 microphones (or line-input) (3.5' male jack connection) (or more for next release)

2 stereo speakers (3.5' male jack connection) (or more for next release)

Bluetooth device ready to communicate by app. (Take as reference a typical mobile phone with an Android version greater than 5.1 (Lollipop) install on it)

What we need:

1. Record sound from microphones and play it by Speakers in a "live" situation ( = very low latency system).

2. Apply some effects to microphones in terms of GAIN and Frequency on each channel input/output

a. WARNING: Gain could be also negative (reverse wave) in order to create a special sound effect.

b. On frequency, in octave band, we need to put (typical) filter like low pass band or high pass band, band equalizer …etc…

3. Play by Speakers the mixed sound with these possibilities:

a. Speaker 1 or 2 could play a combination of sound among the 5 MICs (so we can play MIC 1 and MIC 2 or all MICs or 3 of them and so on) independently. This meaning that we can also play MIC1 and MIC2 on Speaker 1 and MIC3 and MIC5 on Speaker 2 while MIC 4 is off, for example.

b. On each Speaker we can apply a sum of effects like to microphone. These effects can be set differently on each speaker.

4. All these settings are digital, so we need to record the sound, apply effects and choose what is played and what is not by Bluetooth interface in live mode.

Final release of electronic board need also to have:

1. Bluetooth communication on board (as wireless monitor and firmware upgrading).

2. COM port by mini USB female connection (as wired monitor and firmware upgrading).

3. I2C communication port using a RJ45 connector (following the specifications in a document apart) for compatibility to another system.

4. At least n°5 3.5' Jack female connection for the microphones (or more for next release).

5. At least n°2 3.5' Jack female connection for the speakers (or more for next release).

6. 1 connector for 230V power supply.

Minimal constrain:

1. No interference (noise) between the power supply and the sound play by speakers or recorded by microphones. (= EMC compatibility)

2. No interference (noise) between Bluetooth and the sound play by speakers or recorded by microphones. (= EMC compatibility)

3. CPU clock frequency MUST BE FAST enough to avoid problems on latency. DSP system with same constrains is needed also.

4. An SD card used to record sound could be take in consideration but need to be a fast record type.

Is up to you define a list of tecs specs of microphone and speaker compatible with hardware you are design.

Микроконтроллер Electronic Design PCB Design and Layout

ID проекта: #24405011

О проекте

6 заявок(-ки) Удаленный проект Последняя активность 3 года (лет) назад

6 фрилансеров(-а) готовы выполнить эту работу в среднем за €592


Best PCB Design Expert at your doorstep! Dear Client, With more than 5 Years of experience in PCB Design and Circuit Design in Audio based PCB design, I can ensure you quality work and before time delivery. Followin Больше

€500 EUR за 7 дней(-я)
(11 отзывов(-а))

We are a team of Electrical and Electronics engineers and we are Excellent in the following areas: • Embedded C Programming. • VHDL/Verilog, LABView • Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC and STM Больше

€500 EUR за 7 дней(-я)
(6 отзывов(-а))

hello sir, how are you. I read your proposal and i am interested in this project. I am an Embedded engineer (arm, pic, AVR, Arduino, SOC ble chips, ZigBee, WiFi, GPS, LED, LCD display etc.) and PCB designer. You can c Больше

€750 EUR за 20 дней(-я)
(5 отзывов(-а))

hi, i am working as hardware engineer since 10 years. have completed more then 100 designs. i would like to work with you

€500 EUR за 7 дней(-я)
(1 отзыв)

Hello! My name is Anton. I have a lot of experience in Engineering, Electronics, CAD / CAM, Electrical Engineering, PCB Layout, etc. I completely understand your task and I can do it perfectly. I am very fond of thi Больше

€800 EUR за 7 дней(-я)
(0 отзывов(-а))

hello I have experienced in Microcontroller programming with nRF52832 BLE for a long time. You can send me information and I can do it with a cheaper or more reasonable price than everyone. I have a lot of experience Больше

€500 EUR за 7 дней(-я)
(0 отзывов(-а))