Закрыт

Create a simple pcb design using PADS.

Job Description:

Step 1 Create a schematic diagram. You may create your schematic in either Eagle or PADS Logic.

Step 2: Import the schematic diagram into PADS Layout.

Step 3: Create the Gerber files for manufacturing the board

You need to send the following: bottom layer, top layer, outline, and drill. Include the board file as well. The extension changes depending on the software.

Pad Stack 30 mils

Clearance 14 mils

Trace Width Max: 180 mils

Min: 18 mils

•pcb design must meet the following drill bit guidelines:

Function Size (mm) Size (mils)

Trace 0.5 20

Trace 1.00 39

Trace 2.00 79

Drill Hole 0.5 19.7

Drill Hole 0.6 23.6

Drill Hole 0.7 27.6

Drill Hole 0.8 31.5

Drill Hole 0.9 35.4

Drill Hole 1.5 59.1

• Only PCBs from PADS are supported.

Use only the drill size specifications listed above to avoid DRC failure).

The Schematic to be designed is attached to the word document.

Навыки: Разводка печатной платы, Электроника, Схемотехника, Электротехника, Микроконтроллер

О клиенте:
( 6 отзыв(-а, -ов) ) Ikeja, Nigeria

ID проекта: #35333201

27 фрилансеров(-а) готовы выполнить эту работу в среднем за $162

vijay1307

Profile : ---------- over 18 years of experience in PCB layout design. Expertise in EDA layout tools Pads & Allegro. Experience in Ethernet related layout designs with Electrical interface, Optical interface, PHY Больше

$75 USD за 10 дней(-я)
(46 отзывов(-а))
6.3
pilpanikoba

Hello How are you? Thanks for your posting job. I have read your project requirements and I am 100% sure I can complete your project perfectly. ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ I have 15 years experience in Circuit & PC Больше

$200 USD за 7 дней(-я)
(23 отзывов(-а))
6.6
mairajali11

Hello I am Electrical Engineer and a professional PCB designer, I can do your task quite efficiently. I have 5 years of experience designing boards. Check my profile and inbox me to discuss it more. I am a verified an Больше

$200 USD за 7 дней(-я)
(91 отзывов(-а))
6.0
HarimohanG

Good day, I have more than 30 years experience in PCB and schematic diagram designing. I can design schematic diagram with either Eagle or PADS Logic in a quality and timely manner. I can create a simple pcb design usi Больше

$140 USD за 2 дней(-я)
(5 отзывов(-а))
5.2
preetpalsingh33

Hi, Hope you are well. Let us discuss....................................................................

$80 USD за 3 дней(-я)
(40 отзывов(-а))
5.2
Adeel2k14

I am a professional PCB design engineer i have expertise in designing PCB board for industrial level products. I am working as hardware design engineer in a reputed firm based in Germany, where my job is to analyze the Больше

$140 USD за 5 дней(-я)
(35 отзывов(-а))
5.4
Hussain89019k

Hi, -> I saw your proposal and i had check the attach file. -> You SCH , PCB design and manufacturing files mean Gerber and other Fabrication files. -> You use Arduino UNO to measure analog voltages which is detected Больше

$30 USD за 1 день
(14 отзывов(-а))
4.6
NairaDavtyan

Hello there. I have good experience with pcb design and layout. I am senior embedded engineer, so can handle firmware also as well as pcb design. Please contact me and discuss details. Regards.

$300 USD за 7 дней(-я)
(2 отзывов(-а))
4.4
mizakata

I am an expert on Eagle. I can do it very quickly. Do you have any pcb size restrictions? I am a electrical engineer with 6 years of experience.

$240 USD за 5 дней(-я)
(1 отзыв)
1.5
ArtaHovs84

Hi, thank you for submitting your project. I accept all your requirements. I am an Electrical Engineering and RF expert, proficient in PCB design and simulation tools (Altium,PADS, Kicad, Proteus, ...), so can guarante Больше

$100 USD за 5 дней(-я)
(1 отзыв)
0.7
alihussainvohra

I am Embedded hardware Engineer. I have experience of schematic and layout in Altium and Eagle. I will able to provide you in PADS too. Let's start the work.

$250 USD за 10 дней(-я)
(0 отзывов(-а))
0.0
Doctirbit

Hello! I have a lot of experience in embedded systems for over 9 years. Perfect experience in embedded systems and IoT devices. Full cycle production. Preparation for the production of printed circuit boards. Their ass Больше

$200 USD за 7 дней(-я)
(0 отзывов(-а))
0.0
tyleleerking

✔️hello sir, how are you.✔️ I read your proposal and i am interested in this project. I have much experience on Circuit design, Hardware design, PCB design, Firmware, C/C++, Micro Python development. Let us discuss t Больше

$200 USD за 4 дней(-я)
(0 отзывов(-а))
0.0
Vaibhavamrutkar

I have read and understood your problem statement and I will be able to complete the task within 30 days. Best Regards, Akshay

$140 USD за 30 дней(-я)
(0 отзывов(-а))
0.0
trongdai1010

Hi sir, I have a lot of experience in PCB design. I went through your project description. So, I can finish your project quickly, cheaply and with good quality. And more, I want us to have a collaboration on the next p Больше

$100 USD за 3 дней(-я)
(0 отзывов(-а))
0.0
MohitS194

Hello  Today's greetings I reviewed the description you provided. I have vast experience in the design and development of SMPS, motor controller boards, etc. I am pretty confident that I can complete your work in the Больше

$150 USD за 6 дней(-я)
(0 отзывов(-а))
0.0
mikitamoroz

Hi, Dear. I am an electronic engineer and PCB designer. I have designed lots of gadgets, IOT devices, PS units, and so on. I can deliver you high quality design. Thank you.

$140 USD за 3 дней(-я)
(0 отзывов(-а))
0.0
Talhababar300

I am a Embedded system engineer. I can design your pcb in a way you have explain. Kindly DM me so we can discuss your project in detail.

$140 USD за 7 дней(-я)
(0 отзывов(-а))
0.0